Facebook

I do and I do. I told you at least 3times, you're missing stuff. Since u think ure being smarter than the guy making it, I'll just let you do your thing. It's a waste of time to tell somebody the same thing over and over and over again. I cannot diagnose issues if I do not know the initial state, it's that easy. If u have 4 wires left and door control doesn't work you're extremely far off.

Or you just don’t offer technical help on your products without money?

You don’t have a wiring diagram or anything?

Ok, if you says so :)

Everything works fine as soon as I changed the fob battery. It wasn’t lighting up because it wasn’t sensing the fob nearby. I have four wires for door control to hook up and that’s it. Should be pretty simple to remember what wires go where 😂

Fob wouldn't have anything to do with any of the issues you're describing. I cannot tell you what wires go where because I don't know what wires u have. I do know ure missing some just from the pictures, so there is zero chance "everything works"

Fixed it. Key fob batteries were dead. I’ve got everything wired in and working aside from the power door controls. Could you tell me what wires go where?

I see now, the fob antenna is the one I was talking about having a ripped wire. That may be my issue

I talked to the person I bought it from and he said you looked at it and said it was good to go and would only need work if swapping to a LHD car

I tried to jumper the wire that’s torn and I got continuity so I know it was working but even with all 3 sensors it’s not working. Just trying to figure out what it’s looking for.

What are the minimum required items for the button to light up? I shot power to the button and it’s got power and ground. The lights flash if I tap on the sensitivity sensor, the gps is working just fine but the button won’t light up. I got it to do it once but now it won’t. Think maybe the fob battery is dead or maybe a proximity sensor? I’ve got the two side sensors hooked up but the front one has a wire that got torn out of the connecter that I need to repin.

I wouldn't even know where to begin without having it in my hands lol

Ok. Yeah I don’t think the box is getting power. When I had it hooked up the led for the sensitivity sensor wasn’t flashing either

JUST the brakes? they are 12V, but just the brakes alone won't let it start/run/work... the brakes have nothing to do with the button, so if the button didn't light up thats a different issue

Ahhh ok. Is it wanting a 12 volt source or a ground signal?

yes thats the other side

The single pin orange wire comes out of the big connector. The guy I got it from said this is what his brake was plugged into

Matt Bolda, 7111N Holmes St, Gladstone, MO 64118

Where do I send it to?

Yeah I already pulled it back out. I only had the ignition harness, push button and brake pedal wire in as well as the two ground terminals

I understand that. I'm not getting in between you guys lol ... just update me if you need anything. I'm not responsible for any damage. I highly recommend not testing around

True. But it was listed as complete and working.

even if half the stuff is missing you're still getting a deal lol

well, can't complain... thats 1/3 of new

$575

no clue lol how much did you pay?

Cool. Hopefully the seller can refund me some money or something.

I would recommend NOT testing around because you can easily burn up your theft box... they are discontinued and if you find them they are 1000+ bucks

there is ZERO chance that I can diagnose this from here. I don't even know where your wires go lol or what you have/dont have.

I’ve got the gps light flashing so I know it’s getting power and ground. But now the start button won’t even light up

I can tell for sure that if you have a loose wire ANYWHERE, something is missing lol

Fuck

200+ bucks

I really can't tell from here... I don't know what the previous owner did or whoever uninstalled it... I basically gotta go thru the entire harness and see

How much will that run me? I had it started and then unplugged a few things to clean up the wiring for the main harness and push button and now I can’t get it to do anything

this needs to come back to me and get fixed. you're missing connectors, probably even parts

yeah man, this is nowhere close what I sell... whoever took it out, went crazy lol

This is wrapped around the ignition harness and is just a long black wire. Do you have a proper wiring diagram?

Door control I think have also been cut

That’s on the trunk output wire

I see this plug and that’s the last of the OEM plugs I have

I’m having some issues with the brake switch. The issue is I can’t find it on the main harness. Is it just a jumper harness?

good luck!

Thank you! I’ll be installing it tomorrow

No worries

give me like 30min. almost home

oh crap, I totally forgot, sorry

Did you get a chance to find the instructions?

Oh ok. The seller said it did remote start too but I have to sign a waiver? I’ve been wanting this kit for a few years and finally got it for a hell of a deal

u listed everything up there :)

Sounds good. What other options does it do?

I can send u the instructions later... IF anything doesn't work when u drop it in, the kit needs to visit me for inspection since it was in another car.

Oh boy, that's the big one

All I know is it has the gps, trunk popper, push button start and proximity sensors

And which system? I make quite a few for mkiv

94 Supra RHD

Hey for which car?

Hey man, I just recently bought a used push start kit and the seller said you made it. Would you happen to have any install instructions?

Jonathan changed the group photo.

Jonathan named the group Jonathan · Plug and Play Alarms MKIV / SC300 / Soarer w/ Remote Start.